News

How to Choose a 5-Axis Machining Center: T700-3+2 vs TW-400, Parameter by Parameter

By: Ruian Precision Machinery Views: 62 Date: 2026-11-12

Choose T700-3+2 when the part fits within Φ170, weighs under 20 kg, and is mainly aluminium, copper, engineering plastics or light-duty steel — where cycle time, floor space and cost matter most.

Choose TW-400 when the part reaches Φ640 and 200 kg, when steel or stainless needs heavy cutting, or when surface work requires rotary positioning better than 10 arc-seconds.

The dividing line is not the word "5-axis". It is part size and cutting load.

1. Side-by-side parameters

Item

T700-3+2

TW-400

CNC system

SYNTEC 220MA-5

Siemens SINUMERIK ONE (NCU 1750)

Structure

Cradle type

Bridge type, DD dual-drive rotary table

X / Y / Z travel

700 / 400 / 330 mm

500 / 500 / 450 mm

Spindle nose to table

160–490 mm

100–550 mm

Worktable

Φ170 cradle, load 20 / 10 kg

Φ400, load 200 kg, centre bore Φ80H7

5-axis envelope

Limited by Φ170 cradle

Φ640 dia., max height 450 mm

Spindle type

BT30 direct drive

HSK-A63 integrated motor spindle

Spindle speed

20,000 rpm

20,000 rpm

Spindle power / torque

5.5 kW continuous

20 kW / 30 N·m

X/Y/Z servo motors

2.4 / 2.4 / 3.9 kW

3.1 / 3.1 / 3.1 kW

Tilt axis

B: +120° / −30°, 30 rpm, 200 N·m

A: ±120°, 50 rpm, 782 N·m

Rotary axis

C: 360°, 30 rpm, 180 N·m

C: 360°, 140 rpm, 363 N·m

Rotary positioning / repeatability

30″ / 20″ (JIS)

±6″ / 3″ (with circular encoder)

Linear positioning / repeatability

0.005 / 300 mm, 0.003 / 300 mm

±0.005 / 300 mm, ±0.003 / 300 mm

Rapid traverse

48 / 48 / 48 m/min

36 / 36 / 36 m/min

Tool magazine

21 stations, disc, BT30

32 stations, HSK-A63

Guideways / ball screws

30 / 30 / 30 mm; X2816, Y2816, Z3216

35 / 35 / 35 mm; Φ40 × 12

Dimensions / weight

1,800 × 2,351 × 2,200 mm / 3,300 kg

3,554 × 3,450 × 3,000 mm / 7,500 kg

2. Four differences that decide the application

Structure: cradle with harmonic drive vs bridge with direct drive.

The T700-3+2 uses a Φ170 cradle with harmonic drive on the B and C axes — 200 N·m on B, 180 N·m on C. Harmonic drive is compact, near zero backlash and economical, ideal for fine indexing of small parts, but its torque ceiling is what it is. The TW-400 is a bridge machine with a Φ400 table driven by dual direct-drive motors — 782 N·m on A and 363 N·m on C, roughly four and two times higher — with A/C circular encoders closing the loop. No intermediate transmission means rigidity under heavy cutting that a harmonic drive cannot deliver.

Spindle: 5.5 kW light cutting vs 20 kW heavy cutting.

Both are rated 20,000 rpm, which is where most misjudgements start. The T700-3+2 runs a BT30 direct-drive spindle at 5.5 kW; the TW-400 runs an HSK-A63 integrated motor spindle at 20 kW and 30 N·m — 3.6 times the power. HSK-A63 contacts the tool holder on both taper and face, so rigidity under heavy cuts is a class above BT30. BT30 belongs on aluminium, copper, plastics and light steel, where fast tool changes and high spindle speed drive the cost per part. Push BT30 into a deep stainless pocket at heavy depth of cut and the spindle and holder will give out first.

Travel: a longer X does not mean a bigger machine.

The T700-3+2 has 700 mm of X travel, 200 mm more than the TW-400, but that length is headroom for long, slender small parts — Y is only 400 and Z only 330, and the table is a Φ170 cradle. It will not take a Φ400 disc. The TW-400's travel is nearly square (500/500/450) and, with the Φ400 table, covers a Φ640 × 450 mm five-axis envelope.

Accuracy ratings are not the same yardstick.

The T700-3+2 quotes 30″ unidirectional positioning and 20″ repeatability under JIS; the TW-400 quotes ±6″ positioning and 3″ repeatability with full circular-encoder feedback. The numbers differ by roughly five times, and the definitions are not strictly equivalent — but one conclusion holds: for surfaces needing better than 10 arc-seconds, only the TW-400 route will get there.

3. Five questions that settle the model

  1. Maximum part diameter? Beyond Φ170, go TW-400.
  1. Part weight? Up to 20 kg the T700 is fine; beyond that the TW-400's 200 kg table capacity is required.
  1. Main material? Aluminium, copper, plastics and small steel parts run more efficiently on the T700-3+2; steel, stainless and titanium at heavy depth of cut need the TW-400.
  1. How tight is the surface tolerance in arc-seconds? Under 10″, take the TW-400; for general indexing and contouring, 30″ / 20″ is sufficient.
  1. Batch size and cycle time? High-volume small parts favour the T700-3+2 with 48 m/min rapids and a 21-station BT30 magazine; mixed large parts machined in one setup favour the TW-400's 32-station HSK-A63 magazine.

4. Two common mistakes

Mistake one: "700 mm of X beats 500 mm, so the T700 is the bigger machine." Travel length is not work envelope. One is a narrow Φ170 cradle, the other a Φ640 rotary space.

Mistake two: "Both run 20,000 rpm, so performance should be similar." Speed is a ceiling; torque and power decide what you can cut. 5.5 kW and 20 kW are different classes of machine.

5. Recommendation

If the part drawing is not final yet, send us three figures: maximum diameter, part weight, and main material with monthly volume. Those three normally fix the model, and the rest of the spec sheet becomes secondary.

Dongguan Ruian Precision Machinery supplies both cradle-type 5-axis machines (T700-3+2, T600-5 series) and bridge-type 5-axis machines (TW-400 series), and can run a process assessment against your drawing.

6. Frequently asked questions

Can the T700-3+2 machine a Φ400 disc?

No. Its table is a Φ170 cradle rated 20 / 10 kg — a Φ400 disc will neither fit nor stay within the load limit. That part belongs on the TW-400: Φ400 table, 200 kg capacity, Φ80H7 centre bore.

Both spindles run 20,000 rpm, so where does the real difference lie?

In power and torque, not in speed. The T700-3+2 has a BT30 direct-drive spindle at 5.5 kW continuous; the TW-400 has an HSK-A63 motor spindle at 20 kW / 30 N·m. Same speed ceiling, 3.6 times the material removal capacity — and BT30 holder rigidity will not support heavy depths of cut.

Can the T700-3+2 cut stainless steel?

Yes, within light-duty limits: small-diameter tools, shallow depths of cut, finishing and light passes. Deep pockets, heavy depths of cut and long continuous cuts need the TW-400, otherwise spindle power and holder rigidity become the bottleneck first.

What does the TW-400's ±6″ positioning accuracy mean in real machining?

With A/C circular encoders closing the loop, repeatability is 3″. At a 100 mm radius, 6 arc-seconds corresponds to roughly 0.003 mm of positional deviation. That is sufficient for surfaces requiring profile tolerance within 0.01 mm. The T700-3+2's 30″ equates to about 0.015 mm at the same radius — adequate for general indexing and contouring, not for high-precision surfaces.

How should the two five-axis envelope figures be read?

The T700-3+2 quotes no separate five-axis envelope because it is bounded by the Φ170 cradle — in practice it is multi-face machining of small parts. The TW-400 quotes Φ640 diameter and 450 mm maximum height, which covers multi-face work on medium housings and disc-type parts.

21-station BT30 versus 32-station HSK-A63 — what does it actually change?

Magazine capacity sets how many operations one setup can cover. For high-volume small parts, 21 stations is usually enough, with fast tool changes and short cycles. For mixed large parts with many operations, 32 stations reduce the number of re-clampings.

What information do you need before ordering?

Three figures: maximum diameter, part weight, and main material with monthly volume. If a drawing exists, send it and we will run a process assessment.